E.R. Zhdanov1, A.V. Volkov2, A.V. Kryukov3, K.A. Tsvetkov4

1 FSBEI of HE “MIREA – Russian Technological University” (Moscow, Russia)

2-4 JSC “Central Scientific Research Radio Engineering Institute named after Academician A.I. Berg” (Moscow, Russia)

1 zhdanov@ufanet.ru; 3 minyyc@yandex.ru

The possibility of impregnating high-strength fabrics under pressure with a modified binder is considered. The development of high-temperature composites that have not only high strength, but also microwave absorption properties is inextricably linked with new products being developed and the imposition of more stringent tactical and technical requirements on them. For the successful introduction of these composites into the field of mechanical engineering, one of the necessary conditions is the assessment of their stress-strain state at the design stage. This method allows producing the fabric for aircraft details with high strength. The purpose of the study is to evaluate the absorption of microwave waves and study the physical and mechanical characteristics of composites obtained by vacuum infusion.

Zhdanov E.R., Volkov A.V., Kryukov A.V., Tsvetkov K.A. Methodology for optimizing the radio absorption capacity and mechanical strength of composite structural materials. Radiotekhnika. 2024. V. 88. № 9. P. 153−159. DOI: https://doi.org/10.18127/j00338486-202409-15 (In Russian)

1. Gorshenev V.N., Kolesov V.V., Fionov A.S., Jerihman N.S. Mnogoslojnye pokrytija s izmenjaemymi jelektrodinamicheskimi harakteristikami na osnove napolnennyh polimernyh matric. Zhurnal radiotehniki instituta radiotehniki i jelektroniki imeni V.A. Kotel'nikova RAN. 2016. № 11. S. 345–354 (In Russian).
2. Latypova A.F., Kalinin Ju.E. Analiz perspektivnyh radiopogloshhajushhih materialov. Vestnik VGTU. 2012. № 6. S. 70–76 (In Russian).
3. Ivanova V.S., Balankin A.S., Bunin I.Zh., Oksogoev A.A. Sinergetika i fraktaly v materialovedenii. M.: Nauka. 1994. 4 s. (In Russian).
4. Masket M. Techenie odnorodnyh zhidkostej v poristoj srede. M.: Gostoptehizdat. 1949. 58 s. (In Russian).
5. Vinogradov V.M., Goncharenko V.A., Komarov G.V. Modelirovanie v tehnologii polimernyh detalej i izdelij. Plasticheskie massy. 2005. № 1. S. 36–39 (In Russian).
6. Mason K.F. Autoclave quality outside the autoclave? High-Performance Composites. 2006. № 14(2). Р. 44–49.
7. Doneckij K. I., Usacheva M. N., Hrul'kov A. V. Metody infuzii dlja izgotovlenija polimernyh kompozicionnyh materialov (obzor). Ch. 1. Nauchno-tehnicheskij zhurnal «Trudy VIAM». 2022. №6 (112). S. 58–67 (In Russian).
8. Lang D. Aerospace structures: current trends. Composites RTM infusion. 2009. Р. 228–242.
9. Neljub V.A., Grashhenkov D.V., Kogan D.I., Sokolov I.A. Primenenie prjamyh metodov formovanija pri proizvodstve krupnogabaritnyh detalej iz stekloplastikov. Tehnologii polimernyh i kompozicionnyh materialov. Himicheskaja tehnologija. 2012. T. 13. № 12. S. 735–739 (In Russian).
10. Lazarus P. Resin infusion of marine composites. International SAMPE symposium. 1996. №. 41. P. 1447–1458.